I’m here today to answer a frequently asked question!  The question is…  “When I put sealant on my quilled jewelry the coils open up and look ugly.  How can I apply the sealant so this doesn’t happen?”

This is an important issue, and one that you will need to conquer if you make paper quilled jewelry, especially if you sell it.  You’ll want it to look the best possible!

First of all, this issue occurs because almost all sealants are water based.  And what happens when you touch water on paper?  It relaxes the fibers.  This is what causes the coils to open.

There is a very simple (in theory) solution to this problem.  You must apply the sealant in VERY thin layers and allow it to COMPLETELY dry between applications.  In this way the paper is slowly stiffened up.  You will apply a THIN layer to one side, and allow it to dry.  Then you will flip over the piece and apply a thin layer to the other side, and again allow it to dry.  Do this twice and then your piece should be sturdy enough for you to be able to apply a final full layer in all the crevices without disturbing the coils.

But what fun is a post without photos!  Here you can see what happens when the sealant is applied too quickly.  For this example I painted on a thick layer, let it settle and allowed it to dry.  The coils obviously warped, opened up, and stuck together unattractively.  NOT what you want!

How to apply sealant to paper quilled jewelry so the coils won't open up - Honey's Quilling

In this following example, the pretty petal is set into a lid that contains some sealant.  I only left it there for a couple seconds, then took it out and laid it on a tissue to soak up excess sealant and allow it to dry.  As you can see the result is again unattractive and warped.  The coils didn’t open up since they were glued together at one end, but it still warped the shape.

How to apply sealant to paper quilled jewelry so the coils won't open up - Honey's Quilling

 

Instead of dipping the piece into sealant or painting it with a thick layer, you just want to put a little sealant on your brush and very gently brush it over one side.  Let it COMPLETELY dry before doing the same on the other side.  Repeat on both sides.  Finally you can put a thicker layer and get it between the coils without everything warping.

How to apply sealant to paper quilled jewelry so the coils won't open up - Honey's Quilling

Below is another example of putting too much sealant on at once and the resulting opening of the pretty coil.How to apply sealant to paper quilled jewelry so the coils won't open up - Honey's Quilling

Now here is a comparison of two peacock petals.  They both started out nicely coiled.  For the left one I painted on a very thin layer of sealant, allowing it to dry before applying another layer.  For the one on the right I applied way too much sealant, allowing it to soak into the whole petal, which obviously made it uncoil.

How to apply sealant to paper quilled jewelry so the coils won't open up - Honey's Quilling

Here is another tip: The more delicate your pieces are, the more difficult it will be for you to apply sealant carefully.  Look carefully at the two designs below.  They are the same design except that the aqua pieces are made with shorter lengths of paper than the rust colored ones. This makes them more delicate.  I had to be SO careful in applying the sealant to the aqua ones, yet you can tell that there is still some uncoiling going on and some warping of the petal shapes.  But with the rust colored one, I didn’t have to be quite as careful, yet they look SO much better.  As much as a delicate flower looks gorgeous with quilling, when you are making jewelry you sometimes have to go for a more solid look if you don’t want to be SO careful with the sealant.

How to apply sealant to paper quilled jewelry so the coils won't open up - Honey's Quilling

Here is one last photo for you today.  This is one of my peacock earring designs.  I was taking photos before I had completely applied the sealant.  I did apply one layer on each side before taking the left photo.  Notice how pretty the coils are!  I had forgotten that I only put one layer of sealant on each side, though, so I went and did a heavy full layer.  I immediately saw my mistake as the coils opened up.  :'(  It is such a pity when you go through all that time making gorgeous earrings, and then that happens.  I couldn’t bear to list them in my etsy shop after that.  I will probably list them in the clearance section of my zibbet shop due to the mistake, but I haven’t done it yet.

How to apply sealant to paper quilled jewelry so the coils won't open up - Honey's Quilling

I hope this post has helped those who have also been having this issue and are wondering how to make the best paper quilled jewelry you can!  If you have any further questions, do let me know!

If you are wondering what sorts of sealants you can use, click here to view all of my posts on sealants (I am testing more, so more posts are coming!)  If you are looking for a quick answer, I love the product Perfect Paper Adhesive and I use it almost exclusively as my quilling glue of choice, and I also often use it as a sealant.  It comes in both matte and glossy!

Stick around and check out some of the other fun stuff on the blog!

Click here to view FREE paper quilling tutorials!

Click here to view paper quilling tips and tricks!

Click here to view a list of places to buy quilling supplies around the world!

Click here to view some of my own quilling projects, with tips so you can make your own if you’d like!

*This post contains some affiliate links.  If you purchase products through the affiliate links I get a small percentage (at no extra cost to you!).  I only link to products that I believe in and/or love to use myself.  Thank you for supporting my blog!